Instructions for inner hole deburring chamfering cutter

Instructions for inner hole deburring chamfering cutter

2021-08-01 22:06:14 内孔去毛刺倒角刀

Instructions for inner hole deburring chamfering cutter

(integral chamfering deburring tool)

1. The tool needs to be aligned with the center of the hole, otherwise it is easy to be damaged or broken during cutting.去毛刺|倒角|浮动铰刀柄|滚压刀

2. During reverse deburring, make sure that all the edges of the deburring tool pass through the hole and open, and do not lift the tool too fast (lift the tool according to the recommended feed rate or the feed rate adjusted by yourself, do not lift it instantaneously like a drill, and give the tool closing time), otherwise it is easy to break.

3. It is recommended to rotate at about 800-1000 rpm and feed at 200-250mm / min. If you think the chamfer is small, you can appropriately reduce the feed. If you think the chamfer is large, you can appropriately increase the feed.

4. There are many ways to solve the problem of chamfering and deburring during the use of chamfering and deburring tools. This description is only a general description. Please feel free to communicate with us at any time in order to better solve the problem of chamfering and deburring of inner holes.

 去毛刺|倒角|浮动铰刀柄|滚压刀

 

 

Instructions for inner hole chamfering cutter

(equipped with blade type chamfering and deburring tool)

1. The chamfering and deburring tool needs to be aligned with the center of the hole, otherwise it is easy to be damaged or broken during cutting.去毛刺|倒角|浮动铰刀柄|滚压刀

2. During reverse deburring, the deburring tool edge must be confirmed to pass through the hole and bounce open, otherwise the cutting cannot be completed, and the tool cannot be lifted too fast (lift the tool according to the recommended feed rate or the feed rate adjusted by yourself, and it cannot be lifted up instantaneously like a drill, but the tool closing time should be given), otherwise it is easy to break.

3. It is recommended to rotate at about 800-1000 rpm and feed at 200-250mm / min. If you think the chamfer is small, the staff can appropriately reduce the feed. If you think the chamfer is large, you can appropriately increase the feed. The blade deburring tool can control the elasticity of the blade by adjusting the screw tightness at the tail, so as to control the chamfer size.

4. There are many ways to solve the problem of chamfering and deburring during the use of chamfering and deburring tools. This description is only a general description. Please feel free to communicate with us at any time in order to better solve the problem of chamfering and deburring of inner holes.

 去毛刺|倒角|浮动铰刀柄|滚压刀去毛刺|倒角|浮动铰刀柄|滚压刀去毛刺|倒角|浮动铰刀柄|滚压刀

 

 

 

common problem:
As for cross holes, there is a gap of more than 2.5 times between the two cross holes. The effect will be better when using standard products. If the diameter is less than 2.5 times, there may be incomplete chamfering and unclean burr removal. Oval holes and break holes cannot be used.
1. The hardness of the processed material is recommended to be below HRC35 degrees.
2. Rotate the inlet and outlet orifice, only forward rotation is required, and there is no need for forward rotation, reverse rotation or pause.
3. This product tends to deburr because it is flexible cutting and the chamfer angle is not very accurate.
If your workpiece belongs to a cross hole with an aperture ratio less than 2.5 times, we will customize the corresponding blade for you to solve the problem of chamfering and deburring of cross holes with an aperture ratio less than 2.5 times.


Awesome Image

It is a company integrating tool R & D, production and sales, specializing in deburring tools and flexible floating tools

此区块不支持当前模块调用
Telephone consultation
Product Center
Online inquiry
QQ customer service